Customer Reviews

 

 

We've stumbled on this article involving Installing A Bathtub listed below on the net and accepted it made good sense to relate it with you on my blog.

Installing a bath tub isn't specifically brain surgery, however it does need solid plumbing, carpentry, and in some cases, tiling skills. Replacing an old bath tub with a brand-new one is additionally a reasonably difficult task. If the old bathtub is conveniently obtainable, the task can relocate easily; if you need to open up a wall to get rid of the old tub and place the brand-new bathtub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will require a helper to leave the old bathtub and embeded in the brand-new one. Ensure you have actually qualified on your own for the job and also are comfortable trying it. Instead of working with a professional to take control of a halfway-completed project, it is far better to consider using one before you begin. Opportunities are you might need a specialist plumber to make tube connections.
This write-up will help you set up a new bath tub in your shower room if you have already acquired a brand-new tub and don't need to transform the plan of your previous supply of water pipes.
Your devices and material list need to consist of the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Tape Measure


• Pipe Caps


 

Planning for the Installment

First of all, the supporting frame supplied with the bathroom must be fitted (if needed) according to the producer's guidelines. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to make sure that if the faucet features a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets system to prevent strain on the bath tub.
Fit the versatile tap connectors to the bottom of the two faucets making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet through the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you use all of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should now be ready to be fitted in its final position.

 

 

Removing Old Taps

If you need to replace old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is separate the water. After doing so, activate the faucets to drain pipes any type of water staying in the system. The procedure of eliminating the existing taps can be quite problematic due to the limited gain access to that is typically the situation.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the taps. Have a towel all set for the staying water that will come from the pipelines. As soon as the supply pipes have been gotten rid of, make use of the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from turning throughout this process. Once the faucets have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Before going on to fit the new taps, contrast the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new taps to fit.

 

 

Mounting the Tub

Using both wooden boards under its feet, position the tub in the required placement. The wooden boards are handy in uniformly spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 little points.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by checking the level and readjusting the feet on the bathtub till the spirit level reviews level.
To mount taps, fit all-time low of the furthest versatile faucet port to the ideal supply pipe by making a compression sign up with; then do the exact same for the various other tap.
Activate the water supply and also check all joints as well as brand-new pipework for leaks and also tighten them if necessary. Fill up the bath tub and additionally inspect the overflow electrical outlet and the regular outlet for leaks.
Ultimately, fix the bath paneling as defined in the manufacturer's instruction manual. Tiling and also sealing around the tub must wait until the bathtub has been used a minimum of once as this will resolve it right into its final setting.

 

 

Suitable New Touches

If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the connector fits on the plastic tail of the tap and the other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, then you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the faucet in the installing opening in the bath/basin making sure that the washers are in place between the faucet and also the sink. Safeguard the faucet in position with the maker supplied backnut. When the tap is securely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with normal tap connectors. The former kind needs to be linked to the tap ends first, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.

 

 

Tiling Around the Bath tub

In the location where the bath meets the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can move enough to fracture a stiff seal, triggering the water to penetrate the wall surface between the bath and also the tiling, causing problems with dampness and also possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your fixtures and installations. They are sold in tubes and also cartridges, as well as are capable of securing gaps approximately a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill the tub with water before sealing, to permit the movement experienced when the tub remains in use. The sealant can fracture fairly very early if you do not think about this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently available on the market. It is suggested to fit the tiles utilizing waterproof or water-proof adhesive and grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

As a passionate reader about A Step-by-Step Guide to Installing a Bathtub, I figured sharing that excerpt was necessary. Sharing is good. One never knows, you might be doing someone a favor. Many thanks for your time. Please check our blog back soon.

Visit Our Website